logo
Mesaj gönder
Ürünler
Haber Detayları
Evde > Haberler >
How to Measure Hydraulic Motor Internal Leakage: A Case Drain Test Protocol for Radial Piston Motors
Olaylar
Bize Ulaşın
86-574-86361510
Şimdi iletişime geçin

How to Measure Hydraulic Motor Internal Leakage: A Case Drain Test Protocol for Radial Piston Motors

2026-11-16
Latest company news about How to Measure Hydraulic Motor Internal Leakage: A Case Drain Test Protocol for Radial Piston Motors

Torque Loss Is a Symptom, Leakage Is the Cause

When a radial piston motor stops holding a load on a slope, most maintenance teams replace it. In our experience perhaps one third of those motors needed only a distributor plate and a set of piston bushings. The difference between the two decisions is one measurement: case drain flow at rated pressure — ninety minutes and a flow meter, converting a guess into a number.

This is the protocol we use when customers return motors for evaluation, and the one we recommend on site for Poclain MS/MK, Rexroth MCR and JMDG series motors.

Where Internal Leakage Comes From

A radial piston motor has three leakage paths, failing on different timescales:

  • Piston to plunger bushing clearance — wears with contamination and high case pressure; drives most slow torque loss
  • Distributor / flat compensation face — scores when oil film collapses at low speed, high pressure
  • Shaft seal and case joints — external leaks, not volumetric loss, but often confused with it

Only the first two appear in case drain flow — which is why a motor can leak visibly at the shaft and still be internally healthy, and a dry motor can be internally finished.

Test Conditions That Make the Number Meaningful

  1. Oil at 45–50 °C (ISO VG 46), cleanliness 18/16/13 or better
  2. Case drain line open to a calibrated flow meter, then to tank below oil level; no back pressure above 0.1 MPa during the test
  3. Motor coupled to a loading device — a dynamometer, or in the field, a stalled actuator with a pressure relief set below rated pressure
  4. Pressure gauge on the inlet port, tachometer on the output shaft
  5. Run five minutes to stabilise before recording any value

Calculate Volumetric Efficiency

Theoretical flow is speed multiplied by displacement. Volumetric efficiency is then:

ηv = Qt / (Qt + Qleak) × 100%, where Qt = n × Vd / 1000 (L/min), n in r/min and Vd in ml/r.

Worked example, MS125 group at 15,000 ml/r turning 30 r/min: Qt = 450 L/min. A measured case drain of 22 L/min gives ηv = 450 / 472 = 95.3%, which is healthy. A case drain of 90 L/min gives 83.3%, which is a motor on its way out.

Acceptance Bands We Use

Case drain as % of theoretical flowVolumetric efficiencyAssessmentRecommendation
≤ 5%≥ 95%New or freshly rebuilt conditionRecord as baseline
5–10%90–95%Normal service wearRe-test at next 2,000 h interval
10–15%85–90%Advanced wear, torque loss noticeable in duty cyclePlan rebuild; check oil cleanliness first
> 15%< 85%End of life for critical dutyRebuild or replace; investigate contamination source

Two adjustments to these bands: high-hour motors on low-duty applications (winches, positioning drives) often run acceptably at 88%; and any motor driving a machine with a brake-holding requirement should be pulled at 10%, because leakage converts directly into drift.

Field Case: Skid Steer Wheel Motor at 8,500 Hours

A contractor reported an MCR5 wheel motor on a skid steer that would not hold position on a ramp. Bench test showed 18.4% case drain leakage at 25 MPa with oil at 48 °C. Teardown found a scored distributor face and three worn piston bushings with no damage to the crankshaft or housing. Replacement of the distributor plate, bushings and seals restored leakage to 4.1%, at roughly a third of the cost of a new unit. Root cause was a return filter bypass left open after a previous service — the ISO cleanliness code at the reservoir was 21/19/16.

That last number is the point: leakage measurement tells you how worn the motor is, oil analysis tells you why.

What the Test Cannot Tell You

Case drain flow does not separate distributor wear from bushing wear, does not detect a cracked piston, and will read falsely low if the case drain line itself is restricted. It also says nothing about mechanical efficiency — a motor can pass the leakage test and still be noisy because of bearing damage. Where torque loss is accompanied by knock or vibration, the unit needs teardown regardless of the leakage figure.

Standards and References

  • ISO 4392-1 — hydraulic motors, steady-state performance determination
  • ISO 4406 — cleanliness code referenced in the field case above
  • ISO 3448 / ISO VG 46 — test oil grade
  • Helm Tower in-house bench procedure HT-QP-07 for leakage and volumetric efficiency testing

Prepared by the technical service team at Ningbo Helm Tower Noda Hydraulic Co., Ltd. (established 2004, ISO 9001 certified). The acceptance bands above are our field practice for MS/MK, MCR and JMDG series motors, not a substitute for the OEM specification of a specific model code. Spare piston bushings, distributor plates and seal kits are available for the series we manufacture and remanufacture.

Ürünler
Haber Detayları
How to Measure Hydraulic Motor Internal Leakage: A Case Drain Test Protocol for Radial Piston Motors
2026-11-16
Latest company news about How to Measure Hydraulic Motor Internal Leakage: A Case Drain Test Protocol for Radial Piston Motors

Torque Loss Is a Symptom, Leakage Is the Cause

When a radial piston motor stops holding a load on a slope, most maintenance teams replace it. In our experience perhaps one third of those motors needed only a distributor plate and a set of piston bushings. The difference between the two decisions is one measurement: case drain flow at rated pressure — ninety minutes and a flow meter, converting a guess into a number.

This is the protocol we use when customers return motors for evaluation, and the one we recommend on site for Poclain MS/MK, Rexroth MCR and JMDG series motors.

Where Internal Leakage Comes From

A radial piston motor has three leakage paths, failing on different timescales:

  • Piston to plunger bushing clearance — wears with contamination and high case pressure; drives most slow torque loss
  • Distributor / flat compensation face — scores when oil film collapses at low speed, high pressure
  • Shaft seal and case joints — external leaks, not volumetric loss, but often confused with it

Only the first two appear in case drain flow — which is why a motor can leak visibly at the shaft and still be internally healthy, and a dry motor can be internally finished.

Test Conditions That Make the Number Meaningful

  1. Oil at 45–50 °C (ISO VG 46), cleanliness 18/16/13 or better
  2. Case drain line open to a calibrated flow meter, then to tank below oil level; no back pressure above 0.1 MPa during the test
  3. Motor coupled to a loading device — a dynamometer, or in the field, a stalled actuator with a pressure relief set below rated pressure
  4. Pressure gauge on the inlet port, tachometer on the output shaft
  5. Run five minutes to stabilise before recording any value

Calculate Volumetric Efficiency

Theoretical flow is speed multiplied by displacement. Volumetric efficiency is then:

ηv = Qt / (Qt + Qleak) × 100%, where Qt = n × Vd / 1000 (L/min), n in r/min and Vd in ml/r.

Worked example, MS125 group at 15,000 ml/r turning 30 r/min: Qt = 450 L/min. A measured case drain of 22 L/min gives ηv = 450 / 472 = 95.3%, which is healthy. A case drain of 90 L/min gives 83.3%, which is a motor on its way out.

Acceptance Bands We Use

Case drain as % of theoretical flowVolumetric efficiencyAssessmentRecommendation
≤ 5%≥ 95%New or freshly rebuilt conditionRecord as baseline
5–10%90–95%Normal service wearRe-test at next 2,000 h interval
10–15%85–90%Advanced wear, torque loss noticeable in duty cyclePlan rebuild; check oil cleanliness first
> 15%< 85%End of life for critical dutyRebuild or replace; investigate contamination source

Two adjustments to these bands: high-hour motors on low-duty applications (winches, positioning drives) often run acceptably at 88%; and any motor driving a machine with a brake-holding requirement should be pulled at 10%, because leakage converts directly into drift.

Field Case: Skid Steer Wheel Motor at 8,500 Hours

A contractor reported an MCR5 wheel motor on a skid steer that would not hold position on a ramp. Bench test showed 18.4% case drain leakage at 25 MPa with oil at 48 °C. Teardown found a scored distributor face and three worn piston bushings with no damage to the crankshaft or housing. Replacement of the distributor plate, bushings and seals restored leakage to 4.1%, at roughly a third of the cost of a new unit. Root cause was a return filter bypass left open after a previous service — the ISO cleanliness code at the reservoir was 21/19/16.

That last number is the point: leakage measurement tells you how worn the motor is, oil analysis tells you why.

What the Test Cannot Tell You

Case drain flow does not separate distributor wear from bushing wear, does not detect a cracked piston, and will read falsely low if the case drain line itself is restricted. It also says nothing about mechanical efficiency — a motor can pass the leakage test and still be noisy because of bearing damage. Where torque loss is accompanied by knock or vibration, the unit needs teardown regardless of the leakage figure.

Standards and References

  • ISO 4392-1 — hydraulic motors, steady-state performance determination
  • ISO 4406 — cleanliness code referenced in the field case above
  • ISO 3448 / ISO VG 46 — test oil grade
  • Helm Tower in-house bench procedure HT-QP-07 for leakage and volumetric efficiency testing

Prepared by the technical service team at Ningbo Helm Tower Noda Hydraulic Co., Ltd. (established 2004, ISO 9001 certified). The acceptance bands above are our field practice for MS/MK, MCR and JMDG series motors, not a substitute for the OEM specification of a specific model code. Spare piston bushings, distributor plates and seal kits are available for the series we manufacture and remanufacture.